/**
* \file
*
* \brief Instance description for SERCOM1
*
* Copyright (c) 2017 Microchip Technology Inc.
*
* \asf_license_start
*
* \page License
*
* SPDX-License-Identifier: Apache-2.0
*
* Licensed under the Apache License, Version 2.0 (the "License"); you may
* not use this file except in compliance with the License.
* You may obtain a copy of the Licence at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an AS IS BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
* \asf_license_stop
*
*/
#ifndef _SAMD51_SERCOM1_INSTANCE_
#define _SAMD51_SERCOM1_INSTANCE_
/* ========== Register definition for SERCOM1 peripheral ========== */
#if (defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
#define REG_SERCOM1_I2CM_CTRLA (0x40003400) /**< \brief (SERCOM1) I2CM Control A */
#define REG_SERCOM1_I2CM_CTRLB (0x40003404) /**< \brief (SERCOM1) I2CM Control B */
#define REG_SERCOM1_I2CM_CTRLC (0x40003408) /**< \brief (SERCOM1) I2CM Control C */
#define REG_SERCOM1_I2CM_BAUD (0x4000340C) /**< \brief (SERCOM1) I2CM Baud Rate */
#define REG_SERCOM1_I2CM_INTENCLR (0x40003414) /**< \brief (SERCOM1) I2CM Interrupt Enable Clear */
#define REG_SERCOM1_I2CM_INTENSET (0x40003416) /**< \brief (SERCOM1) I2CM Interrupt Enable Set */
#define REG_SERCOM1_I2CM_INTFLAG (0x40003418) /**< \brief (SERCOM1) I2CM Interrupt Flag Status and Clear */
#define REG_SERCOM1_I2CM_STATUS (0x4000341A) /**< \brief (SERCOM1) I2CM Status */
#define REG_SERCOM1_I2CM_SYNCBUSY (0x4000341C) /**< \brief (SERCOM1) I2CM Synchronization Busy */
#define REG_SERCOM1_I2CM_ADDR (0x40003424) /**< \brief (SERCOM1) I2CM Address */
#define REG_SERCOM1_I2CM_DATA (0x40003428) /**< \brief (SERCOM1) I2CM Data */
#define REG_SERCOM1_I2CM_DBGCTRL (0x40003430) /**< \brief (SERCOM1) I2CM Debug Control */
#define REG_SERCOM1_I2CS_CTRLA (0x40003400) /**< \brief (SERCOM1) I2CS Control A */
#define REG_SERCOM1_I2CS_CTRLB (0x40003404) /**< \brief (SERCOM1) I2CS Control B */
#define REG_SERCOM1_I2CS_CTRLC (0x40003408) /**< \brief (SERCOM1) I2CS Control C */
#define REG_SERCOM1_I2CS_INTENCLR (0x40003414) /**< \brief (SERCOM1) I2CS Interrupt Enable Clear */
#define REG_SERCOM1_I2CS_INTENSET (0x40003416) /**< \brief (SERCOM1) I2CS Interrupt Enable Set */
#define REG_SERCOM1_I2CS_INTFLAG (0x40003418) /**< \brief (SERCOM1) I2CS Interrupt Flag Status and Clear */
#define REG_SERCOM1_I2CS_STATUS (0x4000341A) /**< \brief (SERCOM1) I2CS Status */
#define REG_SERCOM1_I2CS_SYNCBUSY (0x4000341C) /**< \brief (SERCOM1) I2CS Synchronization Busy */
#define REG_SERCOM1_I2CS_LENGTH (0x40003422) /**< \brief (SERCOM1) I2CS Length */
#define REG_SERCOM1_I2CS_ADDR (0x40003424) /**< \brief (SERCOM1) I2CS Address */
#define REG_SERCOM1_I2CS_DATA (0x40003428) /**< \brief (SERCOM1) I2CS Data */
#define REG_SERCOM1_SPI_CTRLA (0x40003400) /**< \brief (SERCOM1) SPI Control A */
#define REG_SERCOM1_SPI_CTRLB (0x40003404) /**< \brief (SERCOM1) SPI Control B */
#define REG_SERCOM1_SPI_CTRLC (0x40003408) /**< \brief (SERCOM1) SPI Control C */
#define REG_SERCOM1_SPI_BAUD (0x4000340C) /**< \brief (SERCOM1) SPI Baud Rate */
#define REG_SERCOM1_SPI_INTENCLR (0x40003414) /**< \brief (SERCOM1) SPI Interrupt Enable Clear */
#define REG_SERCOM1_SPI_INTENSET (0x40003416) /**< \brief (SERCOM1) SPI Interrupt Enable Set */
#define REG_SERCOM1_SPI_INTFLAG (0x40003418) /**< \brief (SERCOM1) SPI Interrupt Flag Status and Clear */
#define REG_SERCOM1_SPI_STATUS (0x4000341A) /**< \brief (SERCOM1) SPI Status */
#define REG_SERCOM1_SPI_SYNCBUSY (0x4000341C) /**< \brief (SERCOM1) SPI Synchronization Busy */
#define REG_SERCOM1_SPI_LENGTH (0x40003422) /**< \brief (SERCOM1) SPI Length */
#define REG_SERCOM1_SPI_ADDR (0x40003424) /**< \brief (SERCOM1) SPI Address */
#define REG_SERCOM1_SPI_DATA (0x40003428) /**< \brief (SERCOM1) SPI Data */
#define REG_SERCOM1_SPI_DBGCTRL (0x40003430) /**< \brief (SERCOM1) SPI Debug Control */
#define REG_SERCOM1_USART_CTRLA (0x40003400) /**< \brief (SERCOM1) USART Control A */
#define REG_SERCOM1_USART_CTRLB (0x40003404) /**< \brief (SERCOM1) USART Control B */
#define REG_SERCOM1_USART_CTRLC (0x40003408) /**< \brief (SERCOM1) USART Control C */
#define REG_SERCOM1_USART_BAUD (0x4000340C) /**< \brief (SERCOM1) USART Baud Rate */
#define REG_SERCOM1_USART_RXPL (0x4000340E) /**< \brief (SERCOM1) USART Receive Pulse Length */
#define REG_SERCOM1_USART_INTENCLR (0x40003414) /**< \brief (SERCOM1) USART Interrupt Enable Clear */
#define REG_SERCOM1_USART_INTENSET (0x40003416) /**< \brief (SERCOM1) USART Interrupt Enable Set */
#define REG_SERCOM1_USART_INTFLAG (0x40003418) /**< \brief (SERCOM1) USART Interrupt Flag Status and Clear */
#define REG_SERCOM1_USART_STATUS (0x4000341A) /**< \brief (SERCOM1) USART Status */
#define REG_SERCOM1_USART_SYNCBUSY (0x4000341C) /**< \brief (SERCOM1) USART Synchronization Busy */
#define REG_SERCOM1_USART_RXERRCNT (0x40003420) /**< \brief (SERCOM1) USART Receive Error Count */
#define REG_SERCOM1_USART_LENGTH (0x40003422) /**< \brief (SERCOM1) USART Length */
#define REG_SERCOM1_USART_DATA (0x40003428) /**< \brief (SERCOM1) USART Data */
#define REG_SERCOM1_USART_DBGCTRL (0x40003430) /**< \brief (SERCOM1) USART Debug Control */
#else
#define REG_SERCOM1_I2CM_CTRLA (*(RwReg *)0x40003400UL) /**< \brief (SERCOM1) I2CM Control A */
#define REG_SERCOM1_I2CM_CTRLB (*(RwReg *)0x40003404UL) /**< \brief (SERCOM1) I2CM Control B */
#define REG_SERCOM1_I2CM_CTRLC (*(RwReg *)0x40003408UL) /**< \brief (SERCOM1) I2CM Control C */
#define REG_SERCOM1_I2CM_BAUD (*(RwReg *)0x4000340CUL) /**< \brief (SERCOM1) I2CM Baud Rate */
#define REG_SERCOM1_I2CM_INTENCLR (*(RwReg8 *)0x40003414UL) /**< \brief (SERCOM1) I2CM Interrupt Enable Clear */
#define REG_SERCOM1_I2CM_INTENSET (*(RwReg8 *)0x40003416UL) /**< \brief (SERCOM1) I2CM Interrupt Enable Set */
#define REG_SERCOM1_I2CM_INTFLAG (*(RwReg8 *)0x40003418UL) /**< \brief (SERCOM1) I2CM Interrupt Flag Status and Clear */
#define REG_SERCOM1_I2CM_STATUS (*(RwReg16*)0x4000341AUL) /**< \brief (SERCOM1) I2CM Status */
#define REG_SERCOM1_I2CM_SYNCBUSY (*(RoReg *)0x4000341CUL) /**< \brief (SERCOM1) I2CM Synchronization Busy */
#define REG_SERCOM1_I2CM_ADDR (*(RwReg *)0x40003424UL) /**< \brief (SERCOM1) I2CM Address */
#define REG_SERCOM1_I2CM_DATA (*(RwReg *)0x40003428UL) /**< \brief (SERCOM1) I2CM Data */
#define REG_SERCOM1_I2CM_DBGCTRL (*(RwReg8 *)0x40003430UL) /**< \brief (SERCOM1) I2CM Debug Control */
#define REG_SERCOM1_I2CS_CTRLA (*(RwReg *)0x40003400UL) /**< \brief (SERCOM1) I2CS Control A */
#define REG_SERCOM1_I2CS_CTRLB (*(RwReg *)0x40003404UL) /**< \brief (SERCOM1) I2CS Control B */
#define REG_SERCOM1_I2CS_CTRLC (*(RwReg *)0x40003408UL) /**< \brief (SERCOM1) I2CS Control C */
#define REG_SERCOM1_I2CS_INTENCLR (*(RwReg8 *)0x40003414UL) /**< \brief (SERCOM1) I2CS Interrupt Enable Clear */
#define REG_SERCOM1_I2CS_INTENSET (*(RwReg8 *)0x40003416UL) /**< \brief (SERCOM1) I2CS Interrupt Enable Set */
#define REG_SERCOM1_I2CS_INTFLAG (*(RwReg8 *)0x40003418UL) /**< \brief (SERCOM1) I2CS Interrupt Flag Status and Clear */
#define REG_SERCOM1_I2CS_STATUS (*(RwReg16*)0x4000341AUL) /**< \brief (SERCOM1) I2CS Status */
#define REG_SERCOM1_I2CS_SYNCBUSY (*(RoReg *)0x4000341CUL) /**< \brief (SERCOM1) I2CS Synchronization Busy */
#define REG_SERCOM1_I2CS_LENGTH (*(RwReg16*)0x40003422UL) /**< \brief (SERCOM1) I2CS Length */
#define REG_SERCOM1_I2CS_ADDR (*(RwReg *)0x40003424UL) /**< \brief (SERCOM1) I2CS Address */
#define REG_SERCOM1_I2CS_DATA (*(RwReg *)0x40003428UL) /**< \brief (SERCOM1) I2CS Data */
#define REG_SERCOM1_SPI_CTRLA (*(RwReg *)0x40003400UL) /**< \brief (SERCOM1) SPI Control A */
#define REG_SERCOM1_SPI_CTRLB (*(RwReg *)0x40003404UL) /**< \brief (SERCOM1) SPI Control B */
#define REG_SERCOM1_SPI_CTRLC (*(RwReg *)0x40003408UL) /**< \brief (SERCOM1) SPI Control C */
#define REG_SERCOM1_SPI_BAUD (*(RwReg8 *)0x4000340CUL) /**< \brief (SERCOM1) SPI Baud Rate */
#define REG_SERCOM1_SPI_INTENCLR (*(RwReg8 *)0x40003414UL) /**< \brief (SERCOM1) SPI Interrupt Enable Clear */
#define REG_SERCOM1_SPI_INTENSET (*(RwReg8 *)0x40003416UL) /**< \brief (SERCOM1) SPI Interrupt Enable Set */
#define REG_SERCOM1_SPI_INTFLAG (*(RwReg8 *)0x40003418UL) /**< \brief (SERCOM1) SPI Interrupt Flag Status and Clear */
#define REG_SERCOM1_SPI_STATUS (*(RwReg16*)0x4000341AUL) /**< \brief (SERCOM1) SPI Status */
#define REG_SERCOM1_SPI_SYNCBUSY (*(RoReg *)0x4000341CUL) /**< \brief (SERCOM1) SPI Synchronization Busy */
#define REG_SERCOM1_SPI_LENGTH (*(RwReg16*)0x40003422UL) /**< \brief (SERCOM1) SPI Length */
#define REG_SERCOM1_SPI_ADDR (*(RwReg *)0x40003424UL) /**< \brief (SERCOM1) SPI Address */
#define REG_SERCOM1_SPI_DATA (*(RwReg *)0x40003428UL) /**< \brief (SERCOM1) SPI Data */
#define REG_SERCOM1_SPI_DBGCTRL (*(RwReg8 *)0x40003430UL) /**< \brief (SERCOM1) SPI Debug Control */
#define REG_SERCOM1_USART_CTRLA (*(RwReg *)0x40003400UL) /**< \brief (SERCOM1) USART Control A */
#define REG_SERCOM1_USART_CTRLB (*(RwReg *)0x40003404UL) /**< \brief (SERCOM1) USART Control B */
#define REG_SERCOM1_USART_CTRLC (*(RwReg *)0x40003408UL) /**< \brief (SERCOM1) USART Control C */
#define REG_SERCOM1_USART_BAUD (*(RwReg16*)0x4000340CUL) /**< \brief (SERCOM1) USART Baud Rate */
#define REG_SERCOM1_USART_RXPL (*(RwReg8 *)0x4000340EUL) /**< \brief (SERCOM1) USART Receive Pulse Length */
#define REG_SERCOM1_USART_INTENCLR (*(RwReg8 *)0x40003414UL) /**< \brief (SERCOM1) USART Interrupt Enable Clear */
#define REG_SERCOM1_USART_INTENSET (*(RwReg8 *)0x40003416UL) /**< \brief (SERCOM1) USART Interrupt Enable Set */
#define REG_SERCOM1_USART_INTFLAG (*(RwReg8 *)0x40003418UL) /**< \brief (SERCOM1) USART Interrupt Flag Status and Clear */
#define REG_SERCOM1_USART_STATUS (*(RwReg16*)0x4000341AUL) /**< \brief (SERCOM1) USART Status */
#define REG_SERCOM1_USART_SYNCBUSY (*(RoReg *)0x4000341CUL) /**< \brief (SERCOM1) USART Synchronization Busy */
#define REG_SERCOM1_USART_RXERRCNT (*(RoReg8 *)0x40003420UL) /**< \brief (SERCOM1) USART Receive Error Count */
#define REG_SERCOM1_USART_LENGTH (*(RwReg16*)0x40003422UL) /**< \brief (SERCOM1) USART Length */
#define REG_SERCOM1_USART_DATA (*(RwReg *)0x40003428UL) /**< \brief (SERCOM1) USART Data */
#define REG_SERCOM1_USART_DBGCTRL (*(RwReg8 *)0x40003430UL) /**< \brief (SERCOM1) USART Debug Control */
#endif /* (defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
/* ========== Instance parameters for SERCOM1 peripheral ========== */
#define SERCOM1_CLK_REDUCTION 1 // Reduce clock options to pin 1 for SPI and USART
#define SERCOM1_DLY_COMPENSATION 1 // Compensates for a fast DLY50 element. Assuming 20ns
#define SERCOM1_DMA 1 // DMA support implemented?
#define SERCOM1_DMAC_ID_RX 6 // Index of DMA RX trigger
#define SERCOM1_DMAC_ID_TX 7 // Index of DMA TX trigger
#define SERCOM1_FIFO_DEPTH_POWER 1 // 2^FIFO_DEPTH_POWER gives rx FIFO depth.
#define SERCOM1_GCLK_ID_CORE 8
#define SERCOM1_GCLK_ID_SLOW 3
#define SERCOM1_INT_MSB 6
#define SERCOM1_PMSB 3
#define SERCOM1_RETENTION_SUPPORT 0 // Retention supported?
#define SERCOM1_SE_CNT 1 // SE counter included?
#define SERCOM1_SPI 1 // SPI mode implemented?
#define SERCOM1_SPI_HW_SS_CTRL 1 // Master _SS hardware control implemented?
#define SERCOM1_SPI_ICSPACE_EXT 1 // SPI inter character space implemented?
#define SERCOM1_SPI_OZMO 0 // OZMO features implemented?
#define SERCOM1_SPI_WAKE_ON_SSL 1 // _SS low detect implemented?
#define SERCOM1_TTBIT_EXTENSION 1 // 32-bit extension implemented?
#define SERCOM1_TWIM 1 // TWI Master mode implemented?
#define SERCOM1_TWIS 1 // TWI Slave mode implemented?
#define SERCOM1_TWIS_AUTO_ACK 1 // TWI slave automatic acknowledge implemented?
#define SERCOM1_TWIS_GROUP_CMD 1 // TWI slave group command implemented?
#define SERCOM1_TWIS_SDASETUP_CNT_SIZE 8 // TWIS sda setup count size
#define SERCOM1_TWIS_SDASETUP_SIZE 4 // TWIS sda setup size
#define SERCOM1_TWIS_SUDAT 1 // TWI slave SDA setup implemented?
#define SERCOM1_TWI_FASTMP 1 // TWI fast mode plus implemented?
#define SERCOM1_TWI_HSMODE 1 // USART mode implemented?
#define SERCOM1_TWI_SCLSM_MODE 1 // TWI SCL clock stretch mode implemented?
#define SERCOM1_TWI_SMB_TIMEOUTS 1 // TWI SMBus timeouts implemented?
#define SERCOM1_TWI_TENBIT_ADR 1 // TWI ten bit enabled?
#define SERCOM1_USART 1 // USART mode implemented?
#define SERCOM1_USART_AUTOBAUD 1 // USART autobaud implemented?
#define SERCOM1_USART_COLDET 1 // USART collision detection implemented?
#define SERCOM1_USART_FLOW_CTRL 1 // USART flow control implemented?
#define SERCOM1_USART_FRAC_BAUD 1 // USART fractional BAUD implemented?
#define SERCOM1_USART_IRDA 1 // USART IrDA implemented?
#define SERCOM1_USART_ISO7816 1 // USART ISO7816 mode implemented?
#define SERCOM1_USART_LIN_MASTER 1 // USART LIN Master mode implemented?
#define SERCOM1_USART_RS485 1 // USART RS485 mode implemented?
#define SERCOM1_USART_SAMPA_EXT 1 // USART sample adjust implemented?
#define SERCOM1_USART_SAMPR_EXT 1 // USART oversampling adjustment implemented?
#endif /* _SAMD51_SERCOM1_INSTANCE_ */